Track The Stars Telescope rOTAtor for TTS-160 Panther Mount
This item is discontinued by the manufacturer and is no longer available.
Stock count is accurate & shown in real time.
- This item is out of stock.
- Sign up for back-in-stock alerts to be notified when this item becomes available (account login required).
- This item is out of stock.
- Sign up for back-in-stock alerts to be notified when this item becomes available (account login required).
Equatorial tracking but NO polar alignment
Long exposure astrophotography without polar alignment. Too good to be true… No. With the Telescope rOTAtor installed on the TTS160 Panther mount that’s exactly what you can do. And it’s so simple that beginners can use it and yet so precise that it can match the most experienced experts.
Install and forget
The Telescope rOTAtor is easily installed by inserting the bottom dovetail into the saddle on the telescope mount. The top of the rOTAtor has its dovetail saddle where the telescope is mounted. Connect the power and signal cable and you are ready to take images. The internal software in the mount head controls the speed and direction of the rOTAtor.
rOTAtor
The telescope rOTAtor rotates the entire Optical Tube Assembly or the OTA. This means that any equipment installed on the OTA is rOTAted too. Therefore you can use a piggybacked guide telescope for guiding or taking long-exposure images with telephoto lenses mounted on top of the OTA.
Set up, point and shoot
When using the TTS-160 Panther with the Telescope rOTAtor astrophotography is fast and simple. Setup the mount with the rOTAtor without doing any levelling. Align on two stars and the combined system is ready for imaging. The rOTAtor will automatically wind to the correct side and start derotating when the object has been centred. Guiding is done via the ST4 compatible port on the mount.
Specifications
- Weight: 1.9 kg
- Materials: Aluminum, black hard anodized
- Drive Gear: 100 mm brass worm wheel and stainless steel worm
- Drive Motors: DC Servo motor with high resolution encoder
- Dovetail Size: 3 inch Losmandy style dovetail plate beneath and 3 inch Losmandy style dovetail saddle at the top
- Connectors: Connector for 12V supply (same as mount head supply via split cable), Control signal connector for connection to mount head
- Rotation Angle: 28 Degrees – 1-3 hours rotation (single subs can be as long as that). Rewinds in few seconds to continue imaging.
- Telescope Capacity: 20 kg
- Imaging Capacity: 20 kg (44 lbs)
- Power Supply Needed: 12V 1A – must be the same battery as the one used for the mount head. NEVER use two independant batteries.
- Transport Bag Size: Diameter 180mm (7inch), Length 300mm (12 inch)
Other Information
- Country of Manufacture: Denmark
Equatorial tracking but NO polar alignment
Long exposure astrophotography without polar alignment. Too good to be true… No. With the Telescope rOTAtor installed on the TTS160 Panther mount that’s exactly what you can do. And it’s so simple that beginners can use it and yet so precise that it can match the most experienced experts.
Install and forget
The Telescope rOTAtor is easily installed by inserting the bottom dovetail into the saddle on the telescope mount. The top of the rOTAtor has its dovetail saddle where the telescope is mounted. Connect the power and signal cable and you are ready to take images. The internal software in the mount head controls the speed and direction of the rOTAtor.
rOTAtor
The telescope rOTAtor rotates the entire Optical Tube Assembly or the OTA. This means that any equipment installed on the OTA is rOTAted too. Therefore you can use a piggybacked guide telescope for guiding or taking long-exposure images with telephoto lenses mounted on top of the OTA.
Set up, point and shoot
When using the TTS-160 Panther with the Telescope rOTAtor astrophotography is fast and simple. Setup the mount with the rOTAtor without doing any levelling. Align on two stars and the combined system is ready for imaging. The rOTAtor will automatically wind to the correct side and start derotating when the object has been centred. Guiding is done via the ST4 compatible port on the mount.
Specifications
- Weight: 1.9 kg
- Materials: Aluminum, black hard anodized
- Drive Gear: 100 mm brass worm wheel and stainless steel worm
- Drive Motors: DC Servo motor with high resolution encoder
- Dovetail Size: 3 inch Losmandy style dovetail plate beneath and 3 inch Losmandy style dovetail saddle at the top
- Connectors: Connector for 12V supply (same as mount head supply via split cable), Control signal connector for connection to mount head
- Rotation Angle: 28 Degrees – 1-3 hours rotation (single subs can be as long as that). Rewinds in few seconds to continue imaging.
- Telescope Capacity: 20 kg
- Imaging Capacity: 20 kg (44 lbs)
- Power Supply Needed: 12V 1A – must be the same battery as the one used for the mount head. NEVER use two independant batteries.
- Transport Bag Size: Diameter 180mm (7inch), Length 300mm (12 inch)
- 1x Telescope rOTAtor unit
- 1x Split power cable
- 1x Control interface cable
- 1x Track The Stars medium size transport bag
Equatorial tracking but NO polar alignment
Long exposure astrophotography without polar alignment. Too good to be true… No. With the Telescope rOTAtor installed on the TTS160 Panther mount that’s exactly what you can do. And it’s so simple that beginners can use it and yet so precise that it can match the most experienced experts.
Install and forget
The Telescope rOTAtor is easily installed by inserting the bottom dovetail into the saddle on the telescope mount. The top of the rOTAtor has its dovetail saddle where the telescope is mounted. Connect the power and signal cable and you are ready to take images. The internal software in the mount head controls the speed and direction of the rOTAtor.
rOTAtor
The telescope rOTAtor rotates the entire Optical Tube Assembly or the OTA. This means that any equipment installed on the OTA is rOTAted too. Therefore you can use a piggybacked guide telescope for guiding or taking long-exposure images with telephoto lenses mounted on top of the OTA.
Set up, point and shoot
When using the TTS-160 Panther with the Telescope rOTAtor astrophotography is fast and simple. Setup the mount with the rOTAtor without doing any levelling. Align on two stars and the combined system is ready for imaging. The rOTAtor will automatically wind to the correct side and start derotating when the object has been centred. Guiding is done via the ST4 compatible port on the mount.
Specifications
- Weight: 1.9 kg
- Materials: Aluminum, black hard anodized
- Drive Gear: 100 mm brass worm wheel and stainless steel worm
- Drive Motors: DC Servo motor with high resolution encoder
- Dovetail Size: 3 inch Losmandy style dovetail plate beneath and 3 inch Losmandy style dovetail saddle at the top
- Connectors: Connector for 12V supply (same as mount head supply via split cable), Control signal connector for connection to mount head
- Rotation Angle: 28 Degrees – 1-3 hours rotation (single subs can be as long as that). Rewinds in few seconds to continue imaging.
- Telescope Capacity: 20 kg
- Imaging Capacity: 20 kg (44 lbs)
- Power Supply Needed: 12V 1A – must be the same battery as the one used for the mount head. NEVER use two independant batteries.
- Transport Bag Size: Diameter 180mm (7inch), Length 300mm (12 inch)
Other Information
- Country of Manufacture: Denmark
- 1x Telescope rOTAtor unit
- 1x Split power cable
- 1x Control interface cable
- 1x Track The Stars medium size transport bag